{"title":"Brewing controllers","description":"\u003cp\u003eElectric brewing controllers hand-built in Vancouver: the SV1 for 120V kettles, the SV2 for one 240V element, and the 3V for HERMS and three-vessel breweries.\u003c\/p\u003e","products":[{"product_id":"sv2-electric-brewery-controller","title":"SV2 Electric Brewery Controller","description":"\u003cp\u003e\u003cstrong\u003eWall-mount 240 V control for electric brewing.\u003c\/strong\u003e Runs any 5500W element. Plugs into a standard NEMA 14-30 dryer outlet. No programming, no auto-tuning, no learning curve.\u003c\/p\u003e\n\u003cp\u003eThe Bräu SV2 is a wall-mounted brewing control panel built for electric brewing systems including the Unibräu All-In, Unibräu DrainPro, and BräuPro. It delivers stable mash temperatures, automatic boil-over protection, and switched power for a pump plus a second 120 V accessory.\u003c\/p\u003e\n\u003cp\u003eMounting the panel to the wall keeps it off the brew deck, out of standing water, and away from hot surfaces — with the display and switches at eye level where you actually use them.\u003c\/p\u003e\n\u003ch2\u003eWhat You Need to Run It\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutlet:\u003c\/strong\u003e 240 V, 30 A, NEMA 14-30R — the same receptacle used for an electric clothes dryer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElement:\u003c\/strong\u003e any 240 V element up to 5500 W terminating in a NEMA L6-30 plug.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVessel:\u003c\/strong\u003e any vessel with a 1.5\" tri-clamp thermowell port.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eInternational customers: the SV2 can be supplied without a main plug so the correct connector for your local electrical standard can be fitted.\u003c\/p\u003e\n\u003ch2\u003eBuilt for Continuous Duty\u003c\/h2\u003e\n\u003cp\u003eA 5500 W element draws roughly 23 A continuously for the full length of a boil. The SV2 is built around that reality rather than around a nameplate rating.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOver-specified solid state relay.\u003c\/strong\u003e The SSR is rated well above the maximum element load, so it runs far below its thermal limit through an entire brew day. SSRs fail from heat, and heat comes from running them close to their rating.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHeavy-duty heat sink.\u003c\/strong\u003e The SSR is mounted to an oversized finned heat sink that pulls heat away from the switching device and out of the enclosure, keeping junction temperatures low and service life long.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFull contactor for positive disconnect.\u003c\/strong\u003e Solid state relays typically fail closed, which means a failed SSR can leave an element energized. The SV2 places a full mechanical contactor upstream of the element circuit. When the element switch is off, the circuit is physically broken — not just electronically gated. This is the same disconnect philosophy used in commercial brewing control panels.\u003c\/p\u003e\n\u003ch2\u003eEnclosure and Controls\u003c\/h2\u003e\n\u003cp\u003eThe SV2 is housed in a powder-coated steel enclosure, sized for airflow around the heat sink and finished to resist the wet, humid, and occasionally splashed environment of a brew space.\u003c\/p\u003e\n\u003cp\u003eFront-panel switches are water-resistant and LED-illuminated, so the state of every circuit — element, pump, auxiliary — is visible at a glance from across the room.\u003c\/p\u003e\n\u003cp\u003eAll external cordage is SOOW: oil-resistant, water-resistant, abrasion-resistant flexible cable with a service rating well beyond typical appliance cord. It stays flexible in a cold garage and does not stiffen, crack, or chalk with age.\u003c\/p\u003e\n\u003ch2\u003eControl: Nothing to Program\u003c\/h2\u003e\n\u003cp\u003eThe SV2 is built around the Auber EZboil, a purpose-designed brewing controller rather than a repurposed industrial PID. It ships ready to brew. There is no auto-tune cycle to run, no PID constants to calculate, and no menu structure to learn before your first batch.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMash mode\u003c\/strong\u003e holds a target temperature by modulating element power, maintaining a stable mash without the overshoot and hunting typical of an untuned PID controller.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBoil mode\u003c\/strong\u003e drives the element at a set power percentage. As wort approaches boiling, built-in boil detection automatically steps power down to a preset level at a preset temperature — cutting output before the hot break climbs the side of the kettle. The result is a controlled rolling boil instead of a boil-over, without standing at the panel with a hand on the dial.\u003c\/p\u003e\n\u003ch2\u003eOutputs\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eElement output.\u003c\/strong\u003e NEMA L6-30 twist-lock receptacle, 240 V. The locking connection cannot be pulled loose mid-boil and will not back out under cord weight or thermal cycling.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePump output.\u003c\/strong\u003e Switched 120 V outlet for your wort pump.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAuxiliary output.\u003c\/strong\u003e A second switched 120 V outlet for a chiller pump, a second wort pump, a work light, or any other accessory you want under panel control.\u003c\/p\u003e\n\u003cp\u003eThe two 120 V outlets share a 6 A supply. That is ample for wort pumps, which typically draw 1 to 1.5 A, and for lighting and small accessories. It is not intended for compressor-driven equipment — do not run a glycol chiller from the auxiliary outlet. Give refrigeration its own dedicated circuit.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eController:\u003c\/strong\u003e Auber EZboil with rotary control dial, integrated boil detection, and dual mash\/boil modes\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMain power input:\u003c\/strong\u003e 240 V, NEMA 14-30P, 30 A, 6 ft (1.8 m) SOOW cord\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElement output:\u003c\/strong\u003e 240 V NEMA L6-30R on 6 ft (1.8 m) SOOW cord, rated for elements to 5500 W\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePump output:\u003c\/strong\u003e 120 V switched outlet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAuxiliary output:\u003c\/strong\u003e 120 V switched outlet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCombined 120 V rating:\u003c\/strong\u003e 6 A total, shared across both outlets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitching:\u003c\/strong\u003e over-specified solid state relay on heavy-duty finned heat sink\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety disconnect:\u003c\/strong\u003e full mechanical contactor on the element circuit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTemperature sensing:\u003c\/strong\u003e probe with 1.5\" tri-clamp thermowell\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnclosure:\u003c\/strong\u003e powder-coated steel, wall-mount, water-resistant switchgear\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCordage:\u003c\/strong\u003e SOOW throughout\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSetup:\u003c\/strong\u003e no PID auto-tuning, no programming required\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSV2 Electric Brewery Controller\u003c\/li\u003e\n\u003cli\u003e240 V NEMA 14-30 main power cord\u003c\/li\u003e\n\u003cli\u003eTemperature probe\u003c\/li\u003e\n\u003cli\u003e1.5\" tri-clamp thermowell (50 mm), with the Controller + Thermowell option\u003c\/li\u003e\n\u003cli\u003eWall-mounting hardware\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWorks With\u003c\/h2\u003e\n\u003cp\u003eThe SV2 is the control panel for the Unibräu and Unibräu DrainPro, and BräuPro systems, and will run any setup meeting the requirements above.\u003c\/p\u003e\n\u003cp\u003eCommonly purchased together: 5500W brewing element and tri-clamp thermowell.\u003c\/p\u003e\n\u003ch2\u003eWarranty and Support\u003c\/h2\u003e\n\u003cp\u003eThe SV2 is covered by a 1-year warranty and supported directly by Bräu Supply.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003eNot sure which controller fits your system? \u003ca href=\"\/collections\/brewing-controllers\"\u003eCompare the SV1, SV2 and 3V\u003c\/a\u003e.\u003c\/p\u003e","brand":"Bräu Supply","offers":[{"title":"Controller Only","offer_id":45755138277572,"sku":"ACC-SV2","price":650.0,"currency_code":"USD","in_stock":true},{"title":"Controller + Thermowell (1.5\" tri-clamp 50mm long from flange face)","offer_id":45755138310340,"sku":"ACC-SV2-TW","price":680.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0389\/0597\/files\/magnific-web.jpg?v=1785260201"},{"product_id":"sv1-brewing-controller","title":"SV1 Electric Brewing Controller","description":"\u003ch2\u003eSV1 Brewing Controller\u003c\/h2\u003e\n\u003ch3\u003ePrecision PID Control for Electric Brewing\u003c\/h3\u003e\n\u003cp\u003eMeet the \u003cstrong\u003eSV1 Brewing Controller\u003c\/strong\u003e — our most versatile, easy-to-use PID controller for electric homebrewing. The SV1 delivers precise temperature control to within \u003cstrong\u003e0.1 °C (0.2 °F)\u003c\/strong\u003e, keeping your mash stable, repeatable, and stress-free.\u003c\/p\u003e\n\u003cp\u003eDesigned for brewers who value accuracy and simplicity, the SV1 focuses on the features that matter most: reliable PID control, clear alarms, and straightforward operation—without unnecessary complexity.\u003c\/p\u003e\n\u003ch3\u003eElectric Brewing Controller, Built for Precision\u003c\/h3\u003e\n\u003cp\u003eThe SV1 simplifies mash and temperature management across a wide range of electric brewing setups. Auto-tune PID control adapts to your system, holding target temperatures with exceptional stability during ramps and rests.\u003c\/p\u003e\n\u003cp\u003eWhether you’re managing a mash, monitoring a heat-up to boil, or switching a solenoid valve, the SV1 delivers consistent control with minimal setup.\u003c\/p\u003e\n\u003ch3\u003eWhy Brewers Choose the SV1\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConsistent results\u003c\/strong\u003e — Auto-tune PID algorithm keeps mash temperatures rock steady.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFast, simple setup\u003c\/strong\u003e — Plug-and-play operation with intuitive controls.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrew-ready alerts\u003c\/strong\u003e — Programmable alarms for key stages (e.g., approaching boil).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDurable sensor\u003c\/strong\u003e — 304 stainless probe with 1.5\" tri-clamp mount for sanitary placement.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlexible power\u003c\/strong\u003e — Operates on 100–240 V and supports common homebrew element sizes.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrecision control\u003c\/strong\u003e — Maintain mash temperature within 0.1 °C \/ 0.2 °F.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePID with auto-tune\u003c\/strong\u003e — Adapts automatically to your system for stable control.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAudible alarms\u003c\/strong\u003e — Alerts for temperature thresholds and critical stages.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompact enclosure\u003c\/strong\u003e — Suitable for wall or countertop mounting.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSanitary sensor package\u003c\/strong\u003e — 304 SS probe, 1.5\" tri-clamp, silicone-coated cable, mini stereo jack.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eValve switching\u003c\/strong\u003e — Can operate solenoid valves for fermentation or cooling control.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower handling\u003c\/strong\u003e — Dual voltage: up to 1650 W at 120 V or 3000 W at 240 V. Ships with a standard NEMA 5-15 plug.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-power capable\u003c\/strong\u003e — Use with SV240 to control 5500 W heating elements.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat It Works With\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eElectric brew kettles for mash and boil temperature management.\u003c\/li\u003e\n\u003cli\u003eRIMS and HERMS systems as the primary temperature controller.\u003c\/li\u003e\n\n\u003c\/ul\u003e\n\u003ch3\u003eHow to Use (Quick Start)\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eInstall the 1.5\" tri-clamp temperature probe into your kettle or thermowell.\u003c\/li\u003e\n\u003cli\u003ePlug your heating device into the controller output and connect power.\u003c\/li\u003e\n\u003cli\u003eSet your target temperature and enable PID (run auto-tune on first use).\u003c\/li\u003e\n\u003cli\u003eConfigure alarms to warn of approaching boil or temperature limits.\u003c\/li\u003e\n\u003cli\u003eBrew as usual — the SV1 maintains temperature automatically.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eWhat’s Included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSV1 Brewing Controller with PID control and alarm functionality.\u003c\/li\u003e\n\u003cli\u003e304 stainless temperature probe with 1.5\" tri-clamp fitting.\u003c\/li\u003e\n\u003cli\u003eSilicone-coated probe cable with mini stereo jack connection.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatibility \u0026amp; Safety Notes\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eElectrical\u003c\/strong\u003e — 100–240 V input; up to 1650 W @120 V or 3000 W @240 V.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-power elements\u003c\/strong\u003e — Pair with SV240 for 5500 W element control.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProbe connection\u003c\/strong\u003e — Mini stereo jack; requires a 1.5\" tri-clamp port for sanitary mounting.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety\u003c\/strong\u003e — Use on a GFCI-protected circuit and follow local electrical codes.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eBottom line:\u003c\/strong\u003e The SV1 delivers professional-level temperature stability in a clean, intuitive controller — ideal for dependable mash control and better beer.\u003c\/p\u003e\u003cp\u003eNot sure which controller fits your system? \u003ca href=\"\/collections\/brewing-controllers\"\u003eCompare the SV1, SV2 and 3V\u003c\/a\u003e.\u003c\/p\u003e","brand":"Bräu Supply","offers":[{"title":"60mm Thermowell Included","offer_id":44864207945924,"sku":"ACC-SV1-TW","price":182.0,"currency_code":"USD","in_stock":true},{"title":"No Thermowell","offer_id":44864207978692,"sku":"ACC-SV1","price":149.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0389\/0597\/products\/SV1_45F1.jpg?v=1678332159"},{"product_id":"3v-electric-brewery-controller","title":"3V Three-Vessel Brewing Controller","description":"\u003cp\u003e\u003cstrong\u003eA whole HERMS brewery on one dryer outlet.\u003c\/strong\u003e The 3V runs your hot liquor tank, mash and boil from one wall-mount 240V panel: three temperature controllers with boil-over protection, two element outlets and two pump outlets on a single 30 A circuit. Three RTD probes are in the box. Hand-built in Vancouver, BC.\u003c\/p\u003e\u003ch3\u003eHow a brew day runs on one circuit\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeat strike water:\u003c\/strong\u003e Element Select on HLT. The HLT element heats to strike temperature.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMash:\u003c\/strong\u003e one pump recirculates the mash through the HERMS coil in the hot HLT, and the Mash controller reads the wort coming back from the mash tun.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSparge:\u003c\/strong\u003e the second pump moves hot water from the HLT to the mash tun.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBoil:\u003c\/strong\u003e flip Element Select to Boil. The same 30 A circuit now powers the boil kettle element. Set the boil power %, and the timer starts on its own once the kettle reaches temperature.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003eOnly one 5,500 W element runs at a time, by design. Some three-vessel panels need two circuits or a 50 A service to fire two elements at once; the 3V doesn't.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable class=\"bs-spec-tbl\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eInput\u003c\/th\u003e\n\u003ctd\u003e240V, 30 A · 6 ft (1.8 m) power cord with NEMA 14-30 plug (4-wire, needs a neutral for the 120V pump outlets)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eElements\u003c\/th\u003e\n\u003ctd\u003eTwo NEMA L6-30R twist-lock outlets · 240V elements up to 5,500 W · one at a time (Element Select)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eElement draw\u003c\/th\u003e\n\u003ctd\u003eAbout 23 A at 5,500 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTemperature control\u003c\/th\u003e\n\u003ctd\u003eThree PID controllers: Hot Liquor, Mash, Boil · built-in timers that start automatically when the set temperature is reached · alarms · manual power % for the boil · boil-over protection · alarm relay\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProbes\u003c\/th\u003e\n\u003ctd\u003eThree 3-wire RTD probes included · 1.5\" tri-clamp mount · 50 mm tips · 3 m (10 ft) shielded cords · DIN plugs into the panel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePump outlets\u003c\/th\u003e\n\u003ctd\u003eTwo 120V outlets, each with its own switch (Pump 1, Pump 2)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSafety\u003c\/th\u003e\n\u003ctd\u003eKeyed main switch · contactors that physically cut both elements · solid-state relays on a heat sink · fused control circuit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMounting\u003c\/th\u003e\n\u003ctd\u003ePowder-coated 1.5 mm steel enclosure, 215 × 150 × 210 mm (8.5 × 5.9 × 8.3 in) · mounting flanges 242 mm (9.5 in) across, for a wall or bench\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBuilt\u003c\/th\u003e\n\u003ctd\u003eHand-built and tested in Vancouver, BC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWarranty\u003c\/th\u003e\n\u003ctd\u003e2 years on the controller · 6 months on probes · lifetime parts support\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eIn the box\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e3V control panel with a 6 ft (1.8 m) power cord and NEMA 14-30 plug\u003c\/li\u003e\n\u003cli\u003eThree temperature probes with 3 m (10 ft) shielded cords\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eYou'll also need\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTwo 240V elements up to 5,500 W, plus two L6-30 element cords (our \u003ca href=\"\/products\/240v-element-power-cord-l6-30?variant=46967847551172\"\u003e12 ft pair\u003c\/a\u003e is an add-on above)\u003c\/li\u003e\n\u003cli\u003eUp to two 120V brew pumps\u003c\/li\u003e\n\u003cli\u003eA 1.5\" tri-clamp port on each vessel for its probe\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eElectrical requirements\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eA 240V, 30 A NEMA 14-30R receptacle, the same one an electric clothes dryer uses, on a 30 A double-pole breaker.\u003c\/li\u003e\n\u003cli\u003eWe recommend GFCI protection on every brewing circuit.\u003c\/li\u003e\n\u003cli\u003eHave any new 240V circuit installed by a qualified electrician. Our \u003ca href=\"\/pages\/brewery-electrical-calculator\"\u003eelectrical calculator\u003c\/a\u003e works out the breaker and wire size.\u003c\/li\u003e\n\u003cli\u003ePush twist-lock plugs fully in and turn to lock. See \u003ca href=\"\/pages\/element-twist-lock\"\u003eelement plug safety\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe 3V is the controller that ships with our \u003ca href=\"\/products\/herms-electric-brewery\"\u003eHERMS Electric Brew System\u003c\/a\u003e. Compare all of our controllers on the \u003ca href=\"\/collections\/brewing-controllers\"\u003ebrewing controllers\u003c\/a\u003e page.\u003c\/p\u003e","brand":"Bräu Supply","offers":[{"title":"Default Title","offer_id":46967001252036,"sku":"ACC-3V","price":1800.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0389\/0597\/files\/3V_electric_Brew_Controller.jpg?v=1791320709"}],"url":"https:\/\/brausupply.com\/collections\/brewing-controllers.oembed","provider":"- Bräu Supply","version":"1.0","type":"link"}